Siemens Simodrive Hata Kodları

Simodrive 611 hata kodları, Simodrive fault codes, Simodrive error codes

  • 000        Alarm diagnostics not possible  
  • 001        The drive does not have firmware          
  • 002        Computation time overflow.                                       
  • 003        NMI due to watchdog.            
  • 004        Stack overflow.            
  • 005        Illegal Opcode, Trace, SWI, NMI (DSP)             
  • 006        Checksum test error.
  • 007        Error when initializing.          
  • 020        NMI due to cycle failure              
  • 025        SSI interrupt      
  • 026        SCI interrupt                     
  • 027        HOST interrupt                
  • 028        Actual current sensing during power-up                             
  • 029        Incorrect measuring circuit evaluation  
  • 030        S7 communication error.       
  • 031        Internal data error.    
  • 032        Incorrect number of current setpoint filters       
  • 033        Incorrect number of speed setpoint filters          
  • 034        Axis count function has failed   
  • 035        Error when saving the user data.
  • 036        Error when downloading the firmware.                          
  • 037        Error when initializing the user data.            
  • 039        Error during power section identification.
  • 040        Expected option module is not available.            
  • 041        The firmware does not support the option module.        
  • 042        Internal software error.                   
  • 043        Firmware, option module                          
  • 044        Connection to the option module failed.                
  • 045        Expected option module is axially unequal          
  • 048        Illegal status PROFIBUS hardware                          
  • 106        ABS_POS mode not possible for linear axis                  
  • 107        ABS_NEG mode not possible for a linear                      
  • 108        Block number available twice                         
  • 109        External block change not requested in block                
  • 110        Selected block number does not exist                        
  • 111        GOTO in block number not permissible        
  • 112        Activate traversing task and start referencing, hand-      
  • 113        Activate traversing task and jog, handwheel simulta-     
  • neously
  • 114        Block change enable END in block number ex-         
  • 115        Traversing range start reached 
  • 116        Traversing range end reached   
  • 117        Target position start of the traversing          
  • range   
  • 118        Target position end of the traversing range
  • 119        PLUS software limit switch actuatedP0118.0.     
  • 120        MINUS software limit switch actuated  
  • 121        Jog 1, jog 2 or handwheel simultaneously active              
  • 122        Parameter value range limits violated        
  • 123        Linear encoder for the selected dimension system illegal            
  • 124        Referencing and jog simultaneously started       
  • 125        Falling edge of the reference cam not identified                             
  • 126        ABS_POS for rotary axis, is not possible                        
  • 127        ABS_NEG for rotary axis is not possible without modulo conversion                
  • 128       Target position lies outside the modulo range                          
  • 129        Maximum velocity for a rotary axis with modulo conversion too high                    
  • 130        Controller or pulse enable withdrawn in motion              
  • 131        Following error too high             
  • 132        Drive located after the minus software limit switch        
  • 133        Drive located after the plus software limit switch                           
  • 134        Positioning monitoring has responded                 
  • 135        Standstill monitoring has responded                     
  • 136        Conv.factor,feedforward contr.speed,parameter set,cannot be represented              
  • 137        Conv.factor,pos.contr.output,parameter set,cannot be represented             
  • 138        Conversion factor between the motor and load too       
  • 139        Modulo range and ratio do not match   
  • 140        Minus hardware limit switch                    
  • 141        Plus hardware limit switch                        
  • 142        Input I0.x not parameterized as equivalent zero mark                  
  • 143        Endless traversing and external block change in                       
  • 144        Switching-in switching-out MDI erroneous                        
  • 145        Fixed endstop not reached         
  • 146        Fixed endstop, axis outside the monitoring window       
  • 147        Enable signals withdrawn at the fixed endstop  
  • 148        Velocity in block outside the range
  • 149        Incorrect data for modulo axis with absolute encoder.                 
  • 150        External position reference value < max. Traversing range                      
  • 151        External position reference value < min.
  • 152        Pos.ref.val. and act.val. output via the bus interf. lim-